Mobile Home Bathroom-Redux!

Did your mobile home come with ugly wall board covered in flowers or thin, pale stripes? How about carpet in the bathroom, was that part of the stunning package you’ve been blessed with? We’ve never made it a secret that we’re perturbed by the crappy quality of our home’s construction and the miserable taste of those who decorated it. But, do we sit and complain about it? No, we change it! A couple of years ago we decided to stick with our mobile home rather than building a “stick-built” home. We aren’t made of money and remodeling this joint has to be an economical venture or it just isn’t going to happen. Our first serious endeavor was our master bathroom. This project was a total rebuild from the subfloor up and we did all of the work ourselves. We’ll try to be as specific about brands and products as we can in this post, so here goes!

Bathroom demolition

We tore everything out, including the sub-floor. Giant wasp nests were found in the walls.

Our bathroom was pretty hideous. We had painted it once and the paint was beginning to peel and look pretty bad. The vinyl tub had turned yellow and the floor and fixtures had seen better days. So, we tore everything out. Demolishing the floor was a real treat and a great exercise to get one’s frustrations out! There was quite a let down the moment we were finished tearing it out. It was the moment we had the realization that we could not turn back now…we had to do SOMETHING with our bathroom…we had no choice but to press on.

The flowered wall board on the ends of the tub area was replaced with Georgia Pacific fiberglass mildew and moisture resistant tile backer-board to prevent moisture buildup and water damage to the structure in the future. Although we were not using tile, this seemed the best choice for behind our shower and tub enclosure to protect the framing behind the wall board in the event of water damage. The sub-floor was done with Georgia Pacific Titanium Dryloc plywood, which has a moisture resistant coating.

Georgia Pacific Dryloc subfloor

Ahhh... our new GP Dryloc Subfloor Fiberglass wall board not shown.

Once the sub-floor and wall board were complete, we covered the walls with beadboard, a white, pre-painted wall covering that resembles wainscot. Since this was such a small room and the ceiling was separated from the larger room outside by a doorway, we covered the ceiling with beadboard as well. (There is an entire Internet community devoted to hating and removing the standard “popcorn” ceilings in mobile homes.) This task was not easy and definitely required two people, but ended up looking gorgeous! All of the beadboard was secured with tiny white finishing nails on the edges and LOCTITE heavy duty construction adhesive on the backside.

I cannot tell a lie, the plumbing was not approached easily. We felt very intimidated by the prospect of reconfiguring our water lines, adding a bath/shower fixture set that was not standard mobile home fair, and redirecting the drain line for the bathtub since the old tub had a center drain and the new one was on the end. However, my father was insistent that it could be done, we just had to have confidence! We used plastic compression fittings and installed shut-off valves (see our post on compression fittings here) which all homes should have. We took our time and thought things through and took it one step at a time.

Rope edged bathtub

Rope edged bathtub being installed. New floor in place.

With the walls covered and secured, our new laminate flooring was installed. We chose a beautiful wide plank snap and lock floor at Lowe’s that currently runs about $1.99 per square foot. It’s rated suitable for bathrooms and kitchens and looks like a stone tile. We used a radial arm saw to cut the pieces and a skill saw to cut holes for items like heating vents and toilet drain. The tub and surround we chose were the most expensive part of the remodel, running almost $500 together. The “rope” design around the edges was complemented by a baseboard molding that had a matching edge.

In mobile homes, people are frequently posed with the problem of the slats between wallboards. These have become the bane of our existence! However, in the new bathroom, we took the opportunity to use a trim treatment in these areas to enhance the “cottage” style we were trying to achieve. The moldings we chose complimented the tub design and the toilet seat.

I always wanted a dim light feature in the exhaust fan so when I take a hot bath, the light can be soft and relaxing. In upstate NY, hot baths in the Winter are a must have! The opening in the ceiling would not accommodate any of the fans we could purchase that were not from mobile home supply stores. So we got over our fears of messing with our roof and modified the opening with aluminum venting. It’s a super quiet, lovely addition to our room. We added a simple vanity, brushed nickel fixtures, and repainted a decorative mirror that we had above our bed to place over the vanity. A nice set of towel hooks on the wall finished off the accessories.

Since a small linen closet was torn out in the demolition, storage was now an issue. We purchased a simple pantry cabinet at Home Depot for $99 and found a free dresser on Craigslist that we painted to add a little color to the room. These little touches turned a once miserable bathroom into a sanctuary, a lovely place to start our mornings, and cost a little under $1500 to complete from start to finish.

This was the first in a long list of large projects we took on that Summer. We worked on it for two and a half weekends (5 days) for about 8 hours a day. Demolition took one of those days. Below is a gallery of photos. I hope this bathroom looks as great to you as it does to us. t has been nearly 3 years since we completed it and it still looks as good as new. These are products and design features that are easily obtained and achieved by visiting your local home improvement stores and simply deciding what you want and figuring out ways to make it happen. Please feel free to comment or contact us about this or any project you see on for questions or pep talks for your project! We love to inspire and to get ideas from others.

master bath

New exhaust fan with dimmed light- brushed nickel finish
New exhaust fan with dimmed light- brushed nickel finish
New Floor and insulation installed
New Floor and insulation installed
Spot for sink vanity
Spot for sink vanity
Old popcorn ceiling...Yuck!
Old popcorn ceiling...Yuck!
New snap together laminate flooring
New snap together laminate flooring
Beadboard ceiling and walls with trim molding
Beadboard ceiling and walls with trim molding
New shower surround with fixtures
New shower surround with fixtures
Ceiling treatment for skylight above shower
Ceiling treatment for skylight above shower
Toilet with rope trim toilet seat
Toilet with rope trim toilet seat
New sink vanity with free dresser painted and new decorative knobs.
New sink vanity with free dresser painted and new decorative knobs.
Old re-purposed mirror adds great character to our space!
Old re-purposed mirror adds great character to our space!
$99 linen cabinet from Home Depot
$99 linen cabinet from Home Depot
Towel hooks match "the look"
Towel hooks match "the look"
Beautiful shower and skylight
Beautiful shower and skylight

Happy remodeling!

~The McGees


  1. Hi! I stumbled onto your page from a Google search for "remodeling ideas for mobile home bathrooms" LOL. I just purchased a mobile home, we close on 10/13. The home was built in the 1960's and the bathroom is the same original 1960's funky decor. Green tub, green sink, and green plastic walls. Seems the toilet is the only thing that isn't original. After we're moved and settled, we'd love to update that bathroom. Funny thing is that I love green but it's just a bit too much. I don't think we need to pull the whole thing apart, we can get the tub redone to white, but the green walls and vanity need to go. There's currently a double vanity. I like what you did with the dresser, it actually looks just like the antique one my daughter has that was my grandfather's (it's the original brown finish). We have absolutely NO experience in remodeling, and would like to keep the cost down so any tips you can give will be great. I can always post some pictures after we're moved in. :)

    • Hi Rachel! Thanks for your post.
      You mentioned the dresser in our bathroom. Recently, I've refinished a long French Provincial dresser to use as a vanity with a sink. We will be taking the sink vanity and blue dresser out of the bathroom on this post and replacing them with a longer dresser with a sink on top. I really love the smaller dresser, but the drawers have started to stick over the years and it needs to go.

      My advice to anyone with a mobile home is the same advice my father has always given me. You can put anything in a mobile home that you would in a stick built home. Don't let anyone tell you otherwise. You will just have to modify to accommodate different sizes. We have never replaced anything in our home with anything from a mobile home parts website or store. We have always used standard replacements for everything we've replaced. We have googled and searched Pinterest and watched videos on Youtube galore….Be patient, be kind to one another while working together, and for goodness sake, if you aren't going to invest in paying someone else to do the work, invest in the tools to do the work yourself and learn how to use them. You can do it!!!
      Good luck with your home and all of your projects. Please visit our Facebook page and share pics of any project you'd like us to see. We love seeing your work!

  2. Bathroom looks amazing. My husband and I are also renovating our bathrooms. Where did you purchase the bathtub? Totally live that style!

    Bathtubs for mobile homes are so expensive and hard to find. Thanks

    • Hi Melissa. Thank you for visiting our site and commenting. We purchased our tub at Lowe's. I'm not sure if they sell that model any longer. It has a rope style trim around the top. We moved the little wall behind the tub to allow for a traditional sized tub rather than a smaller mobile home bathtub.

      Good luck with your projects!

  3. Hi, I removed garden tub and replaced with walk in shower years ago and it’s great. I always wanted to turn the old single shower space into a linen clodet, or pull out shelves but can’t think how to do it. I am single lady so any helpful suggestions appreciated!


    • Thanks so much for visiting. Your closet idea sounds like a terrific use for this former shower space. Shower stalls in mobile homes are usually pretty easy to take out. Most often, it just involves removing some screws or tacks holding the stall in place. If there is a shower door, this is usually held in place the same way and while they may look like they're impossible to remove, they are pretty easy most times. Be sure to detach any plumbing fixtures before removing the enclosure and the shower floor pan.

      Once the enclosure and floor tray are removed, get a good look at the walls and ceiling and floor in the space. Make decisions about what cosmetic blemishes there are to cover up. Determine if you want to use some sort of wall covering like paneling or bead board or cedar wood (great choices for cedar lined closets at Home Depot!) to create a new closet space. An easy 2×4 framing can be used to build a simple wall enclosure to make the closet if the area isn't already enclosed with two sides and a back. If it is already an enclosed space, you may just have to cover the walls and trim it, then put up shelves and maybe install a bi-fold door or a closet door.

      I hope these ideas are helpful. If you get it done, please come by our facebook page and share some pics at We love to see what folks are doing with their mobile homes! Good luck with the project!

  4. I see what you mean about the pipe to the sinks..thanks for that tip, mmhmakeover. After I finish replacing my bedroom door, will start on that project. By the way…my interior door jambs are 3 1/4" wide. Found out that some building supply places (not Lowe's or Home Depot) will actually custom build you a pre-hung door with a jamb of 3 1/4" wide and the price is comparable with the standard house doors you would buy at Lowe's or Home Depot….
    If you need doors!

    • Thank you for the info on the doors. As we get older, we keep installing wider doors to accommodate our possible needs as we get older. It's always good to know a good source!

  5. Thanks for posting this re-model. I just put some Shaw vinyl plank flooring in a walnut color for my bedroom and painted it, then put in real baseboards and framed two bedroom windows. Used a lot of painter's putty for those windows as there were cracks all over around the window casing. Now I must start on my bathroom by removing that yellow garden tub. I have a question I hope you can answer.. my garden tub is of course bordered by two walls, and there is a lot of space beside the tub sides that are not resting against a wall. There are at least 18 – 24" of space between the tub and each vanity. If the plumbing is mounted at the corner of the tub, right next to the wall, how hard is it to re-route the plumbing, which enters from the floor of the trailer. There is no shower with this tub, and I do not wish to install a shower. The bathrooms in this mobile home are the size of small bedrooms one on each end. Also, if the plumbing comes up through a big hole in the plywood, should the plywood be replaced to accommodate the re-routing of the plumbing, instead of just trying to patch the plywood where the old plumbing enters the floor? I know this is a lot to ask, but I don't want to make a mess. Thanks!

    • Thanks for visiting, Cally!
      We removed a tub like this in a relative's home a couple of years ago. They installed the washer and dryer in this space and asked us to enclose the plumbing that went to the tub in a folding counter that we built for them. We enclosed ran the plumbing over to where the washer and dryer were going to sit and covered it with a 3/4 inch plywood box that we installed a counter top on top of so they would have a space to fold laundry. The hardest part of this task was getting the drain plumbing detached from the tub. We had to saw it off and plug it with a cap in the floor.

      It's hard for me to envision your particular layout, although you've given a good description. As long as the plumbing to the tub isn't "before" the plumbing for the sinks in the vanity from the water supply, you should be able to cut these lines and cap them securely in the floor Then, you can either fill that plumbing hole in the floor with Great Stuff, then skim it off level with the floor and cover with new flooring, or cover the hole with new plywood if it is too large to fill with Great Stuff.

      It sounds like you've been busy! I'd be interested to hear how your bathroom task turns out. Good luck!

  6. Great transforming and excellent work. A bathroom couldnt get any better than this but can you please tell us what exactly did it cost you ?

  7. My husband is worried about the bead board BC its not moister resistant. I love the look however. Have all had any warping?

    • Thanks for posting Rebecca! In case you don't see this answer on your other comment, here's what I said in response to your first question:

      Thanks for posting, Rebecca! The bead board has held up very well. Right over the shower, there are a couple of spots of some very small dimpling, but you can't see it unless you are standing up close. Hard to believe, but we did that remodel in 2007. So, 9 years ago? It's held up nicely. I am considering painting it this Summer. Since it's the glossy finish bead board, I will need to use Glidden Gripper on it first, but I've used that on bead board before and it worked great. I will post about that once I do. This room does get a lot of moisture, but we put a window in the bathroom and also have a great exhaust fan. So, that keeps the moisture down. It is also well trimmed and caulked so no moisture gets under the bead board, which I think helps a lot. The rest of it, aside from the couple of small areas, still looks as good as the day we put it up. There has been no warping or buckling at all. They do make a bead board that is wider slats and is heavier wood-like product. It is available at Lowe's for about 30$ per sheet. We've looked at that for a while, but , feel like it would be harder to work with, heavier, and the edges are inconsistent as far as chips and such so you'd have to weed through a lot of the sheets to find perfect ones to use. Good luck with your projects! We'd love to see pictures when you're through. You can post them at our facebook page! Happy Remodeling!

  8. I like your explanation it's very simple and your information display style is amazing, keep it up.

  9. I am curious why you continued with the dreaded “strips” if you redid the walls? Why not just put the headboard on all the way across without any spaces?

    • Hi Kathy. Thank you for your question!
      I used the strips because I liked the cottage look they gave. I didn't really have to use them. I could have used some paint or nail hole filler to smooth the seams in between the bead board sheets but I liked the way this looked. Every other room we have we've removed the strips in. They just worked well for my vision in this particular room.

  10. It looks like we have the same bathroom however behind the where the faucets are is covered it seems to be an empty space I took off one board however there is another I want to make s linen closet can you tell me what could be back there?

    • Hi Debbie.

      I'm not sure what could be back there. If you want to have access to your faucets, you should leave an open space or a panel on a wall so you can get into that area. If there is room where you want the linen closet, you can certainly do that, but if one of the walls of the closet will be the wall the faucet access is, you should make sure to put in an access panel or two for the faucet and the showerhead (if the shower is the faucet you are talking about). You always want access to any water outlets into your home. If something breaks, water damage is your worst enemy in a manufactured home…you need access to get them fixed. Good luck with your closet!

  11. Thank you for tye inspiration! I have ugly carpet in my bathroom too. I love the cottage feel in your bathroom. I currently have a garden tub and a stand up shower in my master bath… And no closet or storage space…I was curious if I could close take out the shower put a cut off where the shower was and in close that area to make into a closet? Then replace tub with a tub/stand up shower? Do you think that could be done? I want to go as cheap as possible but yet make it pretty.

    • Thanks for commenting, Gena. Of course, I think you could take out the tub and put a shower and closet in. Just be sure you get a large enough shower stall. We used a shower pan that is about 48" wide so we didn't feel like we were in an RV shower! We like a lot of room. But, they make them smaller than that if you don't need that kind of space in your shower and if you want to accommodate for a closet. Putting a closet in would actually make a great masked area for water access for repairs and such. Be sure to include shut off valves with any new plumbing changes you make so you can avoid future water damage in the area and have ease of repair at the source.

      Good luck!

    • Would anyone have a solution for windows over a garden tub which we would like to remove (garden tub) and replace with a shower.

      • Hi Kim. Thanks for your comment.
        That is a tricky question regarding windows in the wall above a tub. Is it possible remove the tub and reposition the new shower so it doesn't interfere with the windows? Like, turn it the other way for instance? You can take the window out and patch the wall where the window was and put new insulation there, new siding on the outside, and then put the shower in, but that sure seems like a lot of work! If you don't really need the window, but don't wish to remove it, you could cut any sill off flush with the window, remove any opening mechanisms, put insulation in the window area or cover with plywood flush with the wall, then just put your shower stall walls over the top of the window. (This is something I would do :-)) I hope this gives you a few ideas or that you have found solution you will be happy with.
        Good luck with your project!

    • Yes, you can. I did. Don't forget to turn your water off before working on it. I did and wow – a geyser erupted and soaked everything, but we got it under control and nothing was damaged!

      • We've had our share of water geysers too. We have installed shut off valves at every water source in our home. It makes it much easier to repair or install fixtures when you can turn the water off at the source.

  12. did you cover existing walls with bead board or rip out the existing walls and nail up the wood

    • Welcome to our site, Mike. Yes, we covered the existing wall board, but made sure to do the nailing into the studs underneath. This also provided an extra layer of insulation to the room, which has helped make the room feel less drafty.

  13. Great job…enjoyed reading about your remodel.

  14. Thank you for posting all of this wonderful information. I am remodeling our master bathroom. I am ripping out the garden tub and replacing it with a walk in shower. I am going to make the current small shower into a linen closet.
    Love your remodel.

    • That's a great idea! We tore out a bathtub and installed a walk in shower. It's a terrific space and will be much better when we get older and need easier access than a bathtub.
      Good luck with your projects! Please feel free to come back and brag about them, or share them on our facebook page at

    • Hi cheinsohn, I am sure you are finished with your remodeling by now. My son tore out the shower for me (involved a terrible water shooting everywhere fiasco), but things after that went smoothly. I built a linen closet in the 3' space and never have regretted it. I don't know who designs mobile homes, but whoever does is not in the proper line of work. I am left with a yellowed, nasty looking garden tub (I bet most people don't realize it does not have to ever be used to turn that ghastly yellow). I am getting close to removing that tub and I wonder if you can give me any tips on what you did to get your new tub installed. I have a LOT of room at the edges of the tub, enough for a 5' tub, tub-shower, anything. But the plumbing for the current plastic tub is in a corner about 3" from the wall. Did you encounter any problems with the plumbing. Thanks for any tips you can give me.

      • We've not had a problem with plumbing. We just reroute it to wherever we want it to be. The only plumbing we haven't moved is the toilet drain plumbing. We always keep toilets where they originally have been so we don't have to deal with that much work. All other plumbing is easily rerouted. We always use compression fittings because the last a long time and are super easy to install. If there are drains you aren't going to use, you can cut them and cap them off and reroute the drain to the position your new tub requires. One issue we have found though that might be significant is that it's helpful if the tub drain goes straight down, then has a slight slant downward to it. This allows water to drain more easily without backing up in the tub or shower.

  15. is it best to do walls or floors first

    • Hi Faye. Thanks for visiting and commenting.
      We always work from the top down, including when we do demolition. Ceiling, walls, floors, then trim.

  16. Where is the best place to buy a tub that is 54" long and can you use tile on the walls? I can't seem to find a tub shower surround in the right size but this floor is caving in and I need help now! Jill

    • Welcome to the site, Jill!
      You should be able to get a 54" tub at any big box store. You will likely get a better quality one at one of those stores than you would at a mobile home parts store. You can pretty much retrofit any stick built house fixtures in a manufactured home so be confident in making changes with that type of materials. Also, any time you are doing bathroom remodels, be sure to install shut off valves at all of your water sources. These can save a lot of money in water damages and their are cheap and easy to install if you use compression fittings. See our post at… for more info on our experience with these fittings.

      Here's a link to some 54" tubs and surrounds from Home Depot.

      As far as tile goes, I have heard mixed messages. Tile should stick fine on walls. However, we have had wall shifting in our home and if you did a lovely tile wall, you might experience shifting at the joints that could make things fall apart. Perhaps if you install sheetrock wall and/or tile backer on top of that, you will have luck in keeping things intact.
      Good luck with your projects! If you have a chance, please pop over to our facebook page and post some pics. We'd love to see what you're working on!

  17. Your bathroom belongs in a magazine. You and your hub did a ‘fantastic’ job. I see people make over rooms in mobile homes all the time, but what I love is that you guys didn’t spend an arm and a leg and still got a fabulous outcome. Just goes to show that you dont HAVE to spend a ton of money to get amazing results. Very inspiring.

    • Thanks Vanessa! We try to do things efficiently and economically. If we didn't, we'd never get them done. You don't have to spend a ton of money to get great results. Especially in a manufactured home. You may not get back your investment if you spend a lot of money on materials and labor. It is hard to sell a manufactured home since financing and insurance doesn't work in our favor often. Best to get a great look for a low price.

  18. I'm looking to replace lighting in the bathrooms, however, I am concerned how much can a bathroom vanity light weigh without falling off of the wall? I also have the ugly covered panels, I hate those things.
    thank you

    • Thanks for visiting, Lynn. If you fasten a light fixture into a stud, you should be able to support a fairly heavy light fixture. If you are unsure, you can use a method we've used before. We used a 1"x6" piece of wood and created a wood panel to be a decorative support backing for the light fixture. The area we needed to center the light was right in the middle of two studs so we didn't have anything secure to attach it to. Cut the length of wood that will look nice for your purposes and drill a 1-2 inch hole int the center of the board. Once you've painted it or decorated it however you please, pull the lighting wiring through the hole in the board, then mount the board to the wall by attaching it to one or more studs. You can use construction cement as well as screws for additional security if you wish. For the hole, we use a wide circular drill bit that comes in a door knob drilling kit.

      See how we applied this technique in this remodel:

      Good luck!

  19. I am so glad to have found this website! My hubby rescently discovered that our bathroom sink was leaking. It leaked so much that the floor started to bubble over. So we have to tear out the floor! Since we have to go through all the trouble we (we being the hubby) might as well redo the whole bathroom. His main concern though is the water damage to the under belly of our home. We are not exactly sure how long the sink has been leaking. Would have any advice on how to tackle the underbelly dilemma?

    • Hi Leah!
      We're happy you've found us too! We had some water issues as well. If you tear up the subfloor and find that there are joists in the floor that are rotted from the water, you should be able to shore those up with extra pieces of wood. If they are 2x6s, you can cut a piece that will run from a good portion of the damaged board to another good portion or the end piece that runs perpendicular along the edge of the wall. If you mount this new board along the side of the damaged board and connect it to two good sections, this will solve any rotted joist issues. Secondly, as far as the underbelly, you will be able to see from the inside once the sub floor is up what is going on in the house underbelly. There really isn't much more to it than the subfloor, then the joists, then some insulation, then some black plastic wrap that seals it all in. We have purchased rolls of super fiber tape that is specific to mobile home underbelly repair and weren't that impressed with it. We use Gorilla tape just as successfully. But if you find you want it, check out the link to That's where we got it. Perhaps the insulation is saturated with water and you may want to just take a carpet knife and cut open the plastic wrap directly under the sink to let water out and let the floor dry out for a day or so before putting new flooring down and sealing it back up. If you cut the plastic wrap, be sure to seal it back up with tape. It is often damp under mobile homes so you will want to be sure to use either the black tape I mentioned or Gorilla tape for sure because you don't want critters getting up into your sub flooring more easily. I hope this information helps a bit. Please come back and share your progress and feel free to ask any questions. We will help as we are able.

      The McGees

    • In a mobile home, there’s usually just a 3/4 to 5/8 inch subfloor between your final flooring and floor joists. I recently renovated an MH and there were several rotted spots from floor damage. The best thing you can do is use a jig saw or reciprocating saw to cut out and pry away the rotted spots. Then simply cut a new piece to fit, nail it or screw it down. If your joist is rotted, cut a new piece of 2×8 or 2×6 (depends on what your frame was built with) and splice it to an old joist in the good spots. Not difficult at all.

      • Thanks Vanessa. This is exactly what we did. We used a great plywood product called Drydex. It provided a sealed, waterproof subfloor surface for the bathroom where there's potential for water damage.
        It's great to share those tips with folks. They really are easy fixes! We use a Rockwell Versa-Cut saw. It is the best tool investment we've ever made aside from a Kreg Jig.

        • You said you used a "Plywood product called Drydex". Did you coat the plywood with Drydex and if so what kind of Drydex product did you use? I have been unable to find any Drydex Plywood.

          I did however find several types of Drydex products for different types of projects. I am currently redoing a bathroom from the subfloor up and your post was of some interest to me.

          • Thanks for visiting, Paul. The product was Dryloc or DryPly by Georgia Pacific. We purchased it at Lowes. We didn't coat it with anything, it has a water repellent coating.
            Here's the link to their info about it:
            For information on where to buy Georgia-Pacific Plywood, please call 866-249-3639

            Good luck with your bathroom project. When you are finished, please feel free to come to our facebook page and share photos so others can enjoy your hard work and learn from you.

  20. Hi! I want to take out the hideous corner tub we have and replace it with a walk in shower. My main concern is the floor! Is it strong enough? Should I change the subfloor? I've read in other places that tile is too heavy, so before I do all of the work, I just want to know what I'm getting into!!! If you have any comments, please feel free to add them :) Thanks!

    • Hi Nicky. Thanks so much for visiting our site and taking the time to comment. I apologize for the delay in response. No Excuse…no excuse!
      When we redid our master bath, we knew we would never do it again. So, we tore out the plain wafer board subfloor and put in a terrific plywood subfloor made of duraply, which was the waterproof plywood they sold at Lowes at the time. To remove the old, we took a sledgehammer to it. And let me tell you, it was the best time I've ever had working on our mobile home :-).

      Anyhoo, we then put a nice laminate on top of the plywood and then put a large standard size tub and surround in. It has held it fine and I use the bathtub a lot in the Winter for baths. We also removed a hideous garden tub from my mother-in-law's doublewide and put in a beautiful walk in shower.

      Here are some pics of that shower:

      Please forgive the quality, I just grabbed these shots off of a video we did of the whole project we did in her home due to a water heater that burst while she was away on vacation. Nightmare!

      I do not know if tile is too heavy, but we have a 400 lb pellet stove in our home and a weight machine that is easily 450 lbs. These are both fine in our house and are heavy weights in concentrated areas. I also know many people who have had waterbeds in mobile homes so I don't really understand the reasoning behind saying that tile is too heavy for a mobile home. These things travel for hundreds of miles over the road. They are designed to take a load. But, alas, I am just a lowly DIYer so please don't take my word for it. Keep doing your homework.

      Good luck to you on your project and please do come back again!

      All the best,
      The McGees

  21. Pingback: Bitchin’ Kitchen- Mobile Home Kitchen Makeover Part 2 | My Mobile Home Makeover

  22. Your bathroom redo looks awesome! The hubster and I are about to tackle our master bathroom. First off we want to replace the ugly, waste of space – yellowed garden tub!! Then would like to put in an access door that will lead from the bath to the laundry area. To save some $ we would like to reconstruct the cabinets under the sink and then replace the double sink with a single to add more counter space. Will be taking some before pics as well as during and of course the finished room! Of course a new floor, wall color and will paint the cabinets and add hardware for a facelift.

    • Hi Tammba10. Thanks so much for the post! I have so much more remodel information and images that I have not posted yet. I do hope you will come back and share your image links for the work you're planning to do. If you run into a snag and wonder if we had the same experience or wonder how we dealt with something regarding mobile home remodeling projects, please feel free to contact me through the site and I'd be happy share any experience that might be helpful to you. Good luck with your projects!


  23. Pingback: Bathroom Exhaust-You know you want it! (More on Mobile Home Moisture) | My Mobile Home Makeover

  24. This is a great post. We're always looking for smart resources to share with clients and colleagues, and your piece is absolutely worth sharing!

Leave a Reply

Your email address will not be published. Required fields are marked *

  • Save Your Home From Pests! 5 Star!!!